Make sure you can run this tool and load the GUI up before you go offline!
TECHNICOLOR ROUTER LOGIN INSTALL
This is compiled for windows but if you have Python 3 installed see the instructions at the top of the source\autoflashgui.py for installing missing modules so you can run this on any OS (the latest version will ask to install missing modules but if it fails you may have to install them manually). To use this guide you must be on firmware -820-RA or lower (there are reports that the -820-RB variant has the web flashing functionality disabled) or be able to downgrade to it.
This guide is the "new version" which uses the flashing tool developed by Mark Smith as well as the input from the Whirlpool community to enable as many features as possible. That was the motivation to get into this device and re-enable as many features as possible.īy default, the IP address of the modem will be 10.0.0.138. Personally, I think this kind of sucks – as if you decide to use this device with anyone other than Telstra, you lose access to the VoIP functionality, DECT base station, FXO ports. There is no ‘generic’ firmware available that will just give you access to the modem as any other device you would purchase. They are provided directly to Telstra – and as such, has Telstra branded firmware. The newer verstions of this device are the TG800 "Telstra Gateway Max 2" and DJN2103 "Telstra Gateway Frontier", which most of the following will also apply to, if the device has a firmware version low enough, or which it can still be downgraded to. It has 802.11ac, a VDSL / ADSL2 modem (meaning NBN FTTN compatibility), a DECT base station, 2 x FXS ports for analogue ports, and an FXO port, is known for getting high sync speeds for VDSL2, has a high quality internal PCB and power supply and it's power consumption is quite good at 12 watts with WiFi on (typical router config) and 9 watts with WiFi off (typical bridge mode config). The TG799vac, known more commonly in Australia as the “Telstra Gateway Max” is a very capable piece of equipment. I'm selling this modem, how do I securely wipe all the config?.I want to factory reset 17.2 but I don't want to have to re-flash (aka Ghetto Reset!).My firmware is so old that AutoFlashGUI can't authenticate to the modem!.What's that System Extras tab and what can I do in there?.
TECHNICOLOR ROUTER LOGIN FULL
There are settings on the control pane which can set the SSID, passwords etc, but until the router has been sent its full configuration it is in an 'unconfigured' state. We ship the router with a basic configuration which is just enough to get the router to log in to us and fetch its full configuration for your line. In this case our basic ZyXEL is a better choice, or you can configure it manually: Admin and WiFi passwords If you want to use your own PPPoE router. FTTP, FTTPoD - using the red Ethernet WAN port to the fibre termination 'modem'īridge mode: The automatic A&A configuration will not configure these routers as 'bridge'.G.Fast - using the red Ethernet WAN port connected to an existing G.FAST modem.A&A Quick Start sheet: File:DGA4134 Quick Start.pdf.Spec sheet: File:DGA4134-specsheet.pdf (Provided by ZyXEL, details may vary from the actual product!).2 FXS ports, for connecting an analogue phone to a VoIP account.Modem supports VDSL (FTTC) and ADSL/ADSL2+ (Not G.Fast).Some of the support pages for the DGA0122 are also relevant to the DGA4134. They look physically different, but the user interface, and physical ports are very similar. The DGA4134 and the DGA0122 are very similar. This router was introduced as a stop-gap for the DGA0122 in October 2021 due to supply shortages with the DGA0122. These pages are about the Technicolor DGA4134.